View LP101WSA-TLN1_4360118.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specification 1/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 specification for approval title 10.1? wsvga tft lcd customer lge model supplier lg display co., ltd. *model lp101wsa suffix tln1 *when you obtain standard approval, please use the above model name without suffix ( ) preliminary specification ( ) final specification approved by signature / / / please return 1 copy for your confirmation with your signature and comments. products engineering dept. lg display co., ltd prepared by reviewed by signature approved by c. j. jun / manager m. g. park / engineer s. w. paeng / manager www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 2/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 contents no item page cover 1 contents 2 record of revisions 3 1 general description 4 2 absolute maximum ratings 5 3 electrical specifications 3-1 electrical charactreistics 6 3-2 interface connection 7 3-3 lvds signal timing specifications 8 3-4 signal timing specifications 10 3-5 signal timing waveforms 10 3-6 color input data refernece 11 3-7 power sequence 12 4 optical sfecifications 13 5 mechanical characteristics 16 6 reliablity 20 7 international standards 7-1 safety 21 7-2 emc 21 8 packing 8-1 designation of lot mark 22 8-2 packing form 22 9 precautions 23 a appendix. enhanced extended display identification data 25 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 3/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 record of revisions revision no revision date page description edid ver 0.0 oct. 30. 2008 all first draft (preliminary specification) - www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 4/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 1. general description general features active screen size 10.1 inches diagonal outline dimension 235.0(h) 143.0(v) 5.2(d,max.) [mm] pixel pitch 0.2175mmx0.2088mm pixel format 1024 horiz. by 600 vert. pixels rgb strip arrangement color depth 6-bit, 262,144 colors luminance, white 200 cd/m 2 (typ.5 point) power consumption total 2.6 watt(typ.) @ lcm circuit 0.8 watt(typ.), b/l input 1.8 watt(typ.) weight 190g (max.) display operating mode transmissive mode, normally white surface treatment glare treatment of the front polarizer rohs comply yes the lp101wsvga is a color active matrix liquid crystal display with an integral led backlight system. the matrix employs a-si thin film transistor as the active element. it is a transmissive type display operating in the normally white m ode. this tft-lcd has 10.1inches diagonally measured active display area with wsvga resolution(1024 horizontal by 600 vertical pixel array). each pixel is divided into red, green and blue sub-pixels or dots which are arranged in vertical stripes. gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors. the lp101wsa has been designed to apply the interface method that enables low power, high speed, low emi. the lp101wsa is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. in combination with the vertical arrangement of the sub-pixels, the lp101ws1 characteristics provide an excellent flat display for office automation products such as notebook pc. control & data power edid signal & power tft- lcd pa nel (102 4 x 60 0) 1 600 1 1024 cn 1 user conne ctor 40 pin powe r bloc k edid bloc k gip(gate in panel) sour ce dri ver ci rcuit led backli ght as s ? y l vds & t imi ng c ont rol blo ck pwm & vb l www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 5/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 2. absolute maximum ratings the following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. table 1. absolute maximum ratings storage operation 10 20 30 40 50 60 70 80 0 -20 dry bulb temperature [ ] 10 % 20 % 40 % 60 % 90% 80% 0 10 20 30 40 50 60 wet bulb temperature [ ] humidity[(%)rh] parameter symbol values units notes min max power input voltage vcc -0.3 4.0 vdc at 25 5 c operating temperature t op 0 50 c 1 storage temperature h st -20 60 c 1 operating ambient humidity h op 10 90 %rh 1 storage humidity h st 10 90 %rh 1 note : 1. temperature and relative humidi ty range are shown in the figure below. wet bulb temperature should be 39 c max, and no condensation of water. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 6/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 3. electrical specifications 3-1. electrical characteristics the lp101wh1 requires two power inputs. the first logic is employed to power the lcd electronics and to drive the tft array and liquid crystal. the second backlight is the input about led bl with led driver. parameter symbol values unit notes min typ max logic : power supply input voltage v cc 3.0 3.3 3.6 v 1 power supply input current mosaic i cc - 240 270 ma 2 black i cc_max - 270 300 ma 3 power consumption p cc - 0.8 1.0 w 2 power supply inrush current i cc_p - - 1500 ma 4 lvds impedance z lvds 90 100 110 5 backlight : ( with led driver) led power input voltage v led 7.0 12.0 21.0 v 6 led power input current i led - 150 170 ma 7 led power consumption p led - 1.8 2.1 w 7 led power inrush current i led_p - - 1600 ma 8 pwm duty ratio 5 - 100 % 9 pwm jitter - 0 - 0.3 % 10 pwm impedance z pwm 20 40 60 k pwm frequency f pwm 1000 - 5000 hz 11 pwm high level voltage v pwm_h 1.7 - 5.0 v pwm low level voltage v pwm_l 0 - 0.5 v led_en impedance z pwm 20 40 60 k led_en high voltage v led_en _h 3.0 - 5.3 v led_en low voltage v led_en _l 0 - 0.5 v life time 10,000 - - hrs 12 table 2. electrical characteristics www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 7/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 note) 1. the measuring position is the connector of lcm and the test conditions are under 25 , fv = 60hz, black pattern. 2. the specified icc current and power consumption are under the vcc = 3.3v , 25 , fv = 60hz condition whereas mosaic pattern is displayed and fv is the frame frequency. 3. this spec. is the max load condition for the cable impedance designing. 4. the below figures are the measuring vcc condition and the vcc control block lgd used. the vcc condition is same the minimum of t1 at power on sequence. 5. this impedance value is needed to proper display and measured form lvds tx to the mating connector. 6. the measuring position is the connector of lcm and the test conditions are under 25 . 7. the current and power consumption with led driver are under the vled = 12.0v , 25 , dimming of max luminance whereas white pattern is displayed and fv is the frame frequency. 8. the below figures are the measuring vled condition and the vled control block lgd used. vled control block is same with vcc control block. 9. the operation of led driver below minimum dimmi ng ratio may cause flickering or reliability issue. 10. if jitter of pwm is bigger than maximum. it may cause flickering. 11. this spec. is not effective at 100% dimming ra tio as an exception because it has dc level equivalent to 0hz. in spite of acceptable range as defined, the pwm frequency should be fixed and stable for more consistent brightness control at any specific level desired. 12 the life time is determined as the time at which the typical brightness of lcd is 50% compare to that of initial value at the typical led current. these led backlight has 3 strings on it and the typical current of led?s string is base on 20ma. 10% 90% 0.5ms 3.3v 0v 10% 90% 0.5ms 12.0v 0v rising time vcc rising time v led www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 8/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 3-2. interface connection table 3. module connector pin configuration (cn1) this lcd employs one interface connection, a 40 pin connec tor is used for the module electronics interface. 1, interface chips 1.1 lcd : siw, 1port including lvds receiver 1.2 system : * pin to pin compatible with lvds 2. connector 2.1 lcd :lsm gt05q-40s-h10 (locking type) or equivalent 2.2 mating : 2.3 connector pin arrangement 1 40 [lcd module rear view] pin symbol description notes 1 ct1/nc connector test/no connection(reserved) 2 vdd +3.3v power supply 3 vdd +3.3v power supply 4 v edid +3.3v edid power 5 nc no connection 6 clk edid edid clock input 7 data edid edid data input 8 rxin0- lvds differential data input 9 rxin0+ lvds differential data input 10 gnd ground 11 rxin1- lvds differential data input 12 rxin1+ lvds differential data input 13 gnd ground 14 rxin2- lvds differential data input 15 rxin2+ lvds differential data input 16 gnd ground 17 rxclkin- lvds differential clock input 18 rxclkin+ lvds differential clock input 19 gnd ground 20 nc no connection 21 nc no connection 22 gnd ground 23 nc no connection 24 nc no connection 25 gnd ground 26 nc no connection 27 nc no connection 28 gnd ground 29 nc no connection 30 nc no connection 31 vled_gnd led ground 32 vled_gnd led ground 33 vled_gnd led ground 34 ct2/nc connector test/no connection(reserved) 35 s_pwmin system pwm signal input 36 bl_on led enable[note 1] 37 nc no connection 38 vled +5v~+21v led power supply 39 vled +5v~+21v led power supply 40 vled +5v~+21v led power supply [note 1] on: 2.0v ,off:0~0.4v www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 9/ 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 description symbol min max unit notes lvds clock to data skew margin t skew - 400 + 400 ps 85mhz > fclk 65mhz t skew - 600 + 600 ps 65mhz > fclk 25mhz lvds clock to clock skew margin (even to odd) t skew_eo -1/7 + 1/7 t clk - maximum deviation of input clock frequency during ssc f dev - 3 % - maximum modulation frequency of input clock during ssc f mod - 200 khz - description symb ol min max unit notes lvds differential voltage |v id | 100 600 mv - lvds common mode voltage v cm 0.6 1.8 v - lvds input voltage range v in 0.3 2.1 v - 3-3-1. dc specification 3-3-2. ac specification 3-3. lvds signal timing specifications www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 10 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 < clock skew margin between channel > < lvds data format > 3-3-3. data format - lvds 1 port < spread spectrum > time f center f max f min f mod 1 f center * f dev freq. g 0 r 5 r 4 r 3 r 2 r 1 r 0 b 1 b 0 g 5 g 4 g 3 g 2 g 1 de vsync hsync b 5 b 4 b 3 b 2 x b 7 b 6 g 7 g 6 r 7 r 6 r 1 r 0 g 2 g 1 b 3 b 2 r 7 r 6 g 0 b 1 de x current ( nth ) cycle r 5 r 4 b 0 g 5 vsync hsync b 7 b 6 r 3 r 2 g 4 g 3 b 5 b 4 g 7 g 6 previous ( n - 1 ) th cycle next ( n + 1 ) th cycle rclk+ ra+/- rb+/- rc+/- rd+/- www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 11 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 3-4. signal timing specifications table 5. timing table this is the signal timing required at the input of the us er connector. all of the interface signal timing should be satisfied with the following specifications and spec ifications of lvds tx/rx for its proper operation. 3-5. signal timing waveforms condition : vcc =3.3v low: 0.3vcc high: 0.7vcc data enable, hsync, vsync hsync data enable vsync data enable t wh t hp t hfp t hbp t vp t wv t vbp t vfp t wha t wva t clk 0.5 vcc dclk item symbol min typ max unit note dclk frequency f clk - 50.4 - mhz hsync period thp 1320 1344 1362 tclk width t wh 132 136 150 width-active t wha 1024 1024 1024 vsync period t vp 621 625 632 thp width t wv 1 3 5 width-active t wva 600 600 600 data enable horizontal back porch t hbp 144 160 160 tclk horizontal front porch t hfp 20 24 28 vertical back porch t vbp 20 22 24 thp vertical front porch t vfp 0 0 3 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 12 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 3-6. color input data reference the brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. table 7. color data reference color input color data red msb lsb green msb lsb blue msb lsb r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 basic color black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red red (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green green (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 ... ? ? ? green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue blue (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ? ? ? ? blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 13 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 note) 1. do not insert the mating cable when system turn on. 2. valid data have to meet ?3-3. lvds signal timing specifications? 3. lvds, led_en and pwm need to pull-down condition on invalid status. 4. lgd recommend the rising sequence of vled after the vcc and valid status of lvds turn on. table 6. power sequence table led parameter value units min. typ. max. t 8 10 - - ms t 9 0 - - ms t 10 0 - - ms t 11 10 - - ms t 12 0.5 - - ms 3-7. power sequence logic parameter value units min. typ. max. t 1 0.5 - 10 ms t 2 0 - 50 ms t 3 0 - 50 ms t 4 400 - - ms t 5 200 - - ms t 6 200 - - ms t 7 3 - 10 ms t 7 interface signal, v i lvds power supply input vcc 90% 10% 10% 0v 90% t 1 t 2 t 3 t 4 t 5 t 6 0v dimming control signal of led bl pwm 0v (low) t 8 led input voltage vled t 10 led on/off control signal led_en t 11 t 9 valid data 0v valid data 0v (off) 90% 10% t 12 90% www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 14 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 4. optical specification fig. 1 optical characteristic measurement equipment and method table 8. optical characteristics ta=25 c, vcc=3.3v, f v =60hz, f clk = 50.8mhz, i bl = 19 ma parameter symbol values units notes min typ max contrast ratio cr 300 - - 1 surface luminance, white l wh 170 200 - cd/m 2 2 luminance variation white - 1.4 1.6 3 response time tr r + tr d - 16 25 ms 4 color coordinates red rx t.b.d ry t.b.d green gx t.b.d gy t.b.d blue bx t.b.d by t.b.d white wx 0.283 0.313 0.343 wy 0.299 0.329 0.359 viewing angle 5 x axis, right( =0 ) r 30 - - degree x axis, left ( =180) l 30 - - degree y axis, up ( =90 ) u 10 - - degree y axis, down ( =270) d 20 - - degree gray scale 2.2 6 lcd module optical stage(x,y) pritchard 880 or equivalent 50cm optical characteristics are determined after the unit has been ?on? and stable for approximately 30 minutes in a dark environment at 25 c . the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0 . fig. 1 presents additional information conc erning the measurement equipment and method. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 15 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 gray level luminance [%] (typ) l0 t.b.d l7 t.b.d l15 t.b.d l23 t.b.d l31 t.b.d l39 t.b.d l47 t.b.d l55 t.b.d l63 100 note) 1. contrast ratio(cr) is defined mathematically as surface luminance with all white pixels contrast ratio = surface luminance with all black pixels 2. surface luminance is the average of 5 point across the lcd surface 50cm from the surface with all pixels displaying white. for more information see fig 1. l wh = average(l 1 ,l 2 , ? l 5 ) 3. the variation in surface luminance , the panel total variation ( white ) is determined by measuring l n at each test position 1 through 13 and then defined as followed numerical formula. for more information see fig 2. maximum(l 1 ,l 2 , ? l 13 ) white = minimum(l 1 ,l 2 , ? l 13 ) 4. response time is the time required for the display to transition from white to black (rise time, tr r ) and from black to white(decay time, tr d ). for additional information see fig 3. 5. viewing angle is the angle at which the contra st ratio is greater than 10. the angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig 4. 6. gray scale specification * f v = 60hz www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 16 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 fig. 3 response time the response time is defined as the following figure and shall be measured by switching the input signal for ?black? and ?white?. tr r tr d 100 90 10 0 % optical response white black white fig. 2 luminance : active area a : h/4 mm b : v/4 mm points: 13 points h,v active area 1 3 2 5 4 h a b v 6 7 8 9 10 11 12 13 10mm 10mm fig. 4 viewing angle normal y eye = 0 , right = 180 , left = 270 , down = 90 , up www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 17 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 5. mechanical characteristics the contents provide general mechanical characteristics for the model lp101wsa. in addition the figures in the next page are detailed mechanical drawing of the lcd. outline dimension horizontal 235.0 0.5 mm vertical 143.0 0.5 mm thickness 5.2mm (max) bezel area horizontal 226.0 0.5 mm vertical 128.7 0.5 mm active display area horizontal 222.72 0.3 mm vertical 125.28 0.3 mm weight 190.0g (max.) surface treatment glare treatment of the front polarizer www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 18 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 19 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 20 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 [ detail description of side mounting screw ] notes : 1. screw plated through the method of non-electrolytic nickel plating is preferred to reduce possibility that results in vertical and/or horizontal line defect due to the conductive particles from screw surface. * mounting screw length (a) = 1.5(min) /1.8(max) * mounting screw hole depth (b) = 1.8(min) * mounting hole location : 2.8(typ.) * torque : 2.0 kgf.cm(max) (measurement gauge : torque meter) section a-a www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 21 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 6. reliability environment test condition { result evaluation criteria } there should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. no. test item conditions 1 high temperature storage test ta= 60 c, 240h 2 low temperature storage test ta= -20 c, 240h 3 high temperature operation test ta= 50 c, 50%rh, 240h 4 low temperature operation test ta= 0 c, 240h 5 vibration test (non-operating) random, 1.0grms, x,y,z direction test time : each direction 1hour 6 shock test (non-operating) half sine wave, 180g, 2ms one shock of each six faces(i.e. run 180g 6ms for all six faces) 7 altitude operating storage / shipment 0 ~ 10,000 feet (3,048m) 24hr 0 ~ 40,000 feet (12,192m) 24hr www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 22 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 7. international standards 7-1. safety 7-2. emc a) ansi c63.4 ?methods of measurement of radio- noise emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 b) c.i.s.p.r ?limits and met hods of measurement of radio interf ace characteristics of information technology equipment.? international special committee on radio interference. c) en 55022 ?limits and methods of measurement of radio interface characteristics of information technology equipment.? european committee for electrotechnical standardization.(cenelec), 1998 ( including a1: 2000 ) a) ul 60950-1:2003, first edition, underwriters laboratories, inc., standard for safety of information technology equipment. b) can/csa c22.2, no. 60950-1-03 1 st ed. april 1, 2003, canadian standards association, standard for safety of information technology equipment. c) en 60950-1:2001, first edition, european committee for electrotechnical standardization(cenelec) european standard for safety of information technology equipment. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 23 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 8. packing 8-1. designation of lot mark a) lot mark a b c d e f g h i j k l m a,b,c : size(inch) d : year e : month f ~ m : serial no. note 1. year 2. month mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 b nov mark month a oct 6 jun 7 jul 8 aug 9 sep 4 apr 5 may c 3 2 1 dec mar feb jan b) location of lot mark serial no. is printed on the label. the label is attached to the backside of the lcd module. this is subject to change without prior notice. 8-2. packing form a) package quantity in one box : 30 pcs b) box size : tbd www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 24 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1. mo unting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to the module. and the case on which a module is mounted s hould have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protective plat e to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently wi th absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possib le. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions (1) the spike noise causes the mis-operation of circuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lower temperature, it becomes longer.) (3) brightness depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperatur e change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (5) when fixed patterns are displayed for a l ong time, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shall be done by system manufacturers. grounding and shielding methods may be important to minimized the interference. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 25 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make certain that treatment persons are connected to ground through wris t band etc. and don?t touch interface pin directly. 9-3. electrostatic discharge control strong light exposure causes degradation of polarizer and color filter. 9-4. precautions for strong light exposure 9-5. storage (1) when the protection film is peeled off, static el ectricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) the protection film is attached to the polarizer with a small amount of glue. if some stress is applied to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to remain on the polarizer. please carefully peel off the protection film without rubbing it against the polarizer. (3) when the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarize r after the protection film is peeled off. (4) you can remove the glue easily. when the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. 9-6. handling precaution s for protection film when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunlight or fluorescent light. keep the temperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 26 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 appendix a. enhanced extended di splay identification data (eedid tm ) 1/3 t.b.d www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 27 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 appendix a. enhanced extended di splay identification data (eedid tm ) 2/3 t.b.d www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 28 / 28 lp101wsa liquid crystal display ver. 0.0 oct. 30, 2009 appendix a. enhanced extended di splay identification data (eedid tm ) 3/3 t.b.d www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of LP101WSA-TLN1

	To Download LP101WSA-TLN1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .